자유게시판

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and Doors Before a Storm Hits

Before a storm hits and your windows are smashed, boarding them up and doors can protect your home from damage. To accomplish this, you will should have a few things in the go.

First, measure the window's width and height, including the framing (not the trim around it or masonry). Note these measurements down to ensure that you don't lose them.

Preparation

It is always recommended to board up windows and doors before an event like a storm or natural disasters strike. This will reduce damage to property and decrease the chance of a fatality. 24 hour boarding up service up windows - valetinowiki.racing - requires lots of preparation, including buying and measuring plywood boards and identifying the exact size of each window that needs to be covered. It takes time to cut and put in the boards properly. Fortunately this can be simplified by beginning the preparations as soon as you hear of a storm that could be coming in your area. By doing this you will stay clear of a stressful last minute rush and make the process much simpler for you and your employees.

Begin by listening to forecasters for weather and following the guidelines set by your local government. The earlier you begin the process, you'll have more time to collect the materials and keep them in storage without feeling rushed by a storm that is about to hit. Depending on the severity of the event, you may require large quantities of plywood to cover all your windows. Make use of a tape to determine the height and width of each window opening. Make sure to include the framing or trim around each window, and any ledges with extended edges if they are appropriate.

Divide the total width and height of your window by 2 to determine the number of plywood sheets you'll need. For example, if width of your window is 16 inches the thickness of each sheet should be 8 inches. If your exterior is made of wood, drill pilot holes into the plywood sheet to align with the window frame below. This will reduce the chance of splitting when you insert the screws.

For a window opening that is larger than what one sheet of plywood can accommodate cut two sheets that are each half the size of the intended window and set them side-byside on the wall. Cut a piece of 2 by 4 in (5.1 10.2 cm) 10.2 cm) of lumber to the length of the connecting edge between the plywood sheets, and place it on the top of the seam. Then screw 2.25 in (5.7cm) screws into the plywood sheet and through the bracing to join the two together.

Materials

For safety and security, boarding up doorway up windows and doors should be done using only solid materials that will not break under pressure or split in high winds. The most popular material used to secure windows is plywood, which is affordable, readily available and easy to work with. Pick plywood that is of the exterior grade (CDX) since it is more durable and have fewer knots and warps. A more durable option is storm shutters or hurricane shutters, which are erected over existing windows to provide greater protection against shattered glass and boarding up windows weather conditions that can be severe.

Once you've determined the location of the window openings you can measure the height and the width to determine the amount of plywood you'll require. Utilize a power drill to create pilot holes into the sheets of plywood around each window at two-inch intervals. Before attaching the plywood, determine and mark the locations of studs on the wall to ensure that the boards will be fastened securely. If you have wood siding on your property, search for nailheads in order to determine stud locations. If not, you can look for stud positions with your drill. The screws should be driven into the framing, not the sheathing or trim. A plywood panel that is attached to these materials alone could cause a safety risk in the event of severe winds.

If the size of your window is too big for a single piece of plywood, cut two pieces that are each half the size you need and join them using 2 by 4 inches of lumber. Label each sheet of plywood so you know what window it will cover.

Use corrosion-resistant screws long enough to penetrate the sheathing and the studs to attach the plywood panels to your wall. Make sure to drive the screws into the studs such that they are half the depth of the thickness of the plywood however, be cautious not to go too far and cause damage to the structure of your house.

In addition to securing your windows, you should also put up a "No Trespassing" notice on the property, and consider installing polycarbonate security glass such as DefenseLite over your primary windows. These transparent shields adhere to existing glazing to safeguard your doors and windows. They are virtually unbreakable, deterring criminals from breaking in.

Installation

If you live in a region that is prone to hurricanes or are planning to move to one, the best way to protect yourself is to board up your doors and windows before the threat of a storm approaches. This project can be accomplished quickly and effectively but only if make the effort to measure, cut and label your plywood panels before the storm comes.

You'll also need a few other tools, such as a drill (or a hammer and nails if you don't have the power drill) as well as tape, a saw, gloves, a level and safety glasses. It is a good idea to coat the plywood with sealant, as well, to make it waterproof.

Start by measuring each window opening's width and height. Then cut the plywood sheets to fit within the frames. It is recommended to cut the sheets on the spot, as it gives you more control over the exact dimensions of the plywood.

Cut the boards to the size you want using a circular or track saw. Once installed it is necessary to sand them down completely. them. Once you've put your boards in place, screw 3 inch stainless steel hanger bolts into the framing studs that surround each window. Use washers on each bolt and wing nuts to secure them. Make sure that each screw gets through the studs at a minimum of two inches to ensure that the board is strong enough to resist high winds.

If you're building using concrete blocks, you can attach the plywood to the building with galvanized pan-head screws pushed through the overlapping edges of each panel to form bricks or cinder blocks. You'll also need to drill pilot holes into the masonry before screwing corrosion-resistant screws into the holes. This project could take as long as three hours per window, which is why it's essential to begin the process as soon as you hear that a hurricane warning has been issued. This will give you enough time to complete the task prior to the time when the storm is expected to hit.

Maintenance

You should be prepared to put up a security barrier on your doors and windows prior to the onset of a severe storm. This will help you to avoid costly repairs and protect your home from further damage caused by rain, wind flying objects, and other elements.

Having the right materials will make the boarding up process easier and faster to complete. It is important to measure each window precisely. This will ensure the OSB or plywood is fitted snugly, and that it will not be able to slide off easily. If you're using plywood, be sure to use exterior-grade sheets and consider adding an extra layer of protection.

After you have the OSB or plywood taken measurements, mark the locations where the screws will go into the board. Use a drill to predrill holes at 12-inch intervals in the plywood. You can then use hanger bolts to secure the boards in an emergency or catastrophe situation. After the storm is over and the local authorities have given you the all-clear, remove the bolts but keep them in case of a need in the future.

The next step is to install the plywood panels on top of the windows. This is a two-person task, so be prepared before starting. If you are using plywood, sand the edges to smooth them so that they don't scratch paint or damage trim. Then use corrosion-resistant screws to join the plywood with the pilot holes. If your home has shingles made of vinyl it, nail the plywood directly to the shingles, and not to the wood framing.

A window that is boarded up can be used to stop burglars. The burglars will be more likely to target a structure with a damaged window or one that is not locked. They're also more likely break into the store that has been boarded up as opposed to one that's not. This is something that retail business owners should take very seriously.