자유게시판

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change your door lock is a simple and inexpensive way to increase the security of your home. However, the process is not for all. It requires a certain amount patience and skill.

It is necessary to replace the cylinder, which is located inside the knob's body. The cylinder is what recognizes the key once it's placed into the lock.

Remove the old lock

First, you must remove the lock that was previously in place. It's a straightforward process, however you must keep a few things in your mind. First, make sure that the lock you choose to install is the correct size for the door you have. This will ensure that it fits securely and does not leave a gap in the deadbolt plug or latch.

Once you have removed the latch plate, look for two bolts or screws on the inside of the casing that secure the casing and halves of the lock. Remove these screws using a screwdriver and then pull the lock from the door. If you have a mortise locking, there may be a set screw located at the base of the handle that holds it to the spindle. Remove the doorknobs by unscrewing this screw with the help of a screwdriver.

You should also remove the deadbolt latch and latch plug from the hole in the door jamb. Install your new lock. If you're replacing a mortise you must measure the distance between your upvc window lock replacement double glazing window locks repairs lock repairs (just click the next web page)'s case and your door edge to make sure that your new lock fits.

Many reasons could cause you to replace your door lock, for instance believing that someone else has the key or welcoming an incoming roommate. In any event, you can save money by taking the lock off yourself, rather than hiring an expert to remove it. The process is simpler than many people think and can be completed in just a few minutes.

Start by taking the handle and trim from your door. With a flat screwdriver remove the trim. You will be able twist off the majority of it, and in certain cases the handles may fall off entirely. The next step is to search for a pinhole on the inside of the handle and insert an unstraightened clip into it. This will trigger the release mechanism, allowing you to take off the handle. Then, look for another small tab on the interior of the lock, and press it with a flat screwdriver. After the spindle is removed, you are able to take off the cylinder and housing.

Selecting a new lock

When it comes to choosing the right lock for your home, you have many choices. Take a look at the various types of locks and pick one that is in keeping with the style of your door. Take into consideration the backset which is the distance between the edge and the center of the hole for the lock. Also, think about the cross bore, a small hole in the middle of your door's frame. Select a lock that is suitable for the door thickness and swing.

The majority of door locks are assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they stand up to use and how difficult they are to pick or disable. A grade 3 lock could be a good choice for a tranquil suburban apartment complex, whereas an entry grade lock could hold up better to the traffic that is frequented by a store front on a city street.

Most smart door locks require a digital code to open. If you're concerned about hacking or other security concerns, consult with a professional locksmith or the local police department for advice.

Replace the cylinder

If your door lock cylinder is broken or damaged you can repair it in just a few minutes using a simple DIY project. The key is to select the correct cylinder and follow the instructions that accompany it. The first step is to take off the handle or knob should there be one and then remove the trim around the base of the lock cylinder using the aid of a screwdriver. Once the trim has been removed, you can remove the screws that hold the cylinder with a flathead. The cylinder can then be gently pulled out of the door.

Before installing the new cylinder, be sure it's the right length for the door you are using. With a tape measure, measure the distance between the center of the cylinder and the right and left sides. Purchase a new cylinder that has the same measurements. This will prevent the cylinder from snapping, which could happen when the door is kicked in or when the key sticks inside.

If you have a suitable replacement cylinder, put it in the door lock window repairs and turn the key. This will ensure that the cylinder is aligned with the carrier, which is typically located on the outside of the lock. Then, loosen the set screws that should be just a couple of turns inside the head. You will also need to loosen the screw at the edge of the door that holds the case in place, should there be one.

After taking the lock cylinder out, you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. Installing the part that connects a cylinder to a lock indicator stem is also important. This can be done by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Then, you can connect the remaining smaller bracket to the back of the cylinder. Then, you should put back in the strike plate and latch plate as well as the retaining ring attached to the top of the lock the cylinder.

Installing the new lock

Begin by measuring the door's width if you are replacing an existing lock. Most locksets for residential use are designed for a door thickness of 1 3/8 - 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This will include longer screws as well as an extension for the spindle or a longer tail piece for door knobs.

Most locks come equipped with a thorough installation guide to aid you. Before you begin, go through the instructions to ensure that you've followed the steps. The booklet will give you a good idea of the level of skill that is required to complete the task. You might want to ask a friend who has worked with locks for assistance if you are changing a lock the first time.

Before installing the new lock it's recommended to cover the holes with tape the old hardware. This will keep the screws from slipping out of the holes and safeguard any tile you may have installed in the area. It also protects against potential damage from rust dirt, and grime. SECURAM Touch includes the masking strip or gaffer tape, but you can use any tape you own.

Once you've removed the screws that connect the inside of the lock section to the outside side, pull it straight away. This should be done swiftly to prevent the lock from closing accidentally and damaging the mechanism.

Install the new latch bolt into the upper cross bore of your new lock, if it has one. Make sure that you put it in the correct place, which is usually marked by an arrow on the faceplate. Then, screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate into the door jamb. Test the deadbolt by throwing it few times to ensure that it extends all way into the strike plate and is fully secured. Follow the instructions included with your electronic smart lock to program it. This involves downloading an app and registering your email address, verifying your identity and connecting to the wireless network in order to add your device.