자유게시판

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first line of defense is your door lock. It will prevent unauthorized entry cost to replace upvc door lock mechanism your home. Signs of wear and tear, and also instances like moving into a new house or burglaries, could trigger the necessity of replacing your lock.

To begin, determine the size of your cylinder by measuring the distance between the adjustment screw and the middle of the cylinder knob. This measurement will assist you select the appropriate lock.

Deadbolt

If you want to ensure your door is secure against criminals, it's a great idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe, it makes it harder for an intruder to break through the door. A single-cylinder deadbolt can be activated by a key located on the exterior, and the thumb-turn mechanism located on the interior. A deadbolt will only work if it's installed correctly, though.

The first step is to determine if the door has a hole to install deadbolts, or if it has to be bored. Utilizing the template included with your lock installation kit, mark the location of the deadbolt hole on the door's surface. Then, use the tape measure to determine the height the deadbolt needs to be. Mark this height on the door edge and use speedsquares to draw a straightline across the mark that you made to mark the bolt hole.

Then, use a power drill to drill this area until the hole extends to the other side of the door. This may take some time. Sand the hole and the edge of the door to smooth it. It's also a good idea to paint or stain the door at this point.

When the door is in place take off any screws that are visible on the existing deadbolt. This will reveal both the front and rear assemblies of the deadbolt, as well as its internal bolt. Remove the bolt and replace door lock it with a new one to match the door hardware. You'll need to remove the bolt from a setplate. After that, you'll have to chisel the surface of the door frame to accommodate the strike plate.

If your strike plate is misaligned it's likely that the previous installer didn't correctly mortise it or a weatherstripping came along and changed the strike's position. It is necessary to re-mortise the strike plate and perhaps even the deadbolt to fix the issue. Once you have completed this, test the deadbolt by closing and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

It can make your home and business less secure If the knob on your door is worn. It could also make opening and closing the door more difficult, which is why it is a good idea for you to replace lock upvc door the knob. Replacing knobs is an simple DIY project that shouldn't take more than 30 minutes to complete. You can use a screwdriver and pliers to remove the old knob or handle, but be careful not to scratch any other parts on the door.

Before starting, you'll want to spray WD-40 or some other dry lubricant on the mechanism of the knob on your door. This will help the new lock move smoothly when you turn it. It's essential to select an excellent knob and handle that is compatible with your doors currently in order to ensure that the lock replacement upvc door is operating properly. If you don't have a doorknob that is compatible and handle, you'll need to purchase a new one.

To begin the replacement process, first look over the knob or handle to see what screws hold it in place. If there aren't any screws to hold it in place, you can use a screwdriver to secure the cover plate into the hidden screws plate.

After removing the old knob examine it for indications of damage and rust. If the knob has any dents or marks, you'll have clean it. Otherwise, it shouldn't require any major work.

It's time to install the new knob. You should first examine the two knobs in order to make sure that you've chosen the correct one for your door. You'll want to pick one with an extended rod that's designed to lock into the rod mechanism of the second knob. After you've placed the new knob in the hole in the door and then carefully insert it into the latch.

Thread the latch plate screws downwards, then test the spring by pressing down on it several times. The latch should then spring back up every time. Then, you can install the new knob and lock it with the rod mechanism on the previous knob. Thread the long screws of the interior doorknob through the cylinder holes on the outside knob and fix it in its place.

Latch

A latch is a metallic piece that extends into the doorjamb in order to hold it shut. The latch can be operated via a knob or handle on the inside of the door, or by a thumb-turn on the outside. A deadbolt can be used to secure a latch and keep intruders from breaking through the glass of the door. It can also protect against accidental or intentional closing by children or animals. The latch can be fitted with a single cylinder deadbolt or double cylinder deadbolts, based on the level of security you prefer.

Installing a deadbolt can be the same as installing a latch, however, there are some distinctions. First, measure the setback of the doorjamb by using a tape measure to make sure that the new lock will fit. The setback is the distance between the edge of the doorjamb to the middle of the hole for the faceplate for the latch. The standard setback is 2 3/8 to 2. 3/4 inches. If you have a larger setback, you might need to purchase a more substantial latch at a hardware store or locksmith.

The next step is to drill an edge bore hole in the doorjamb to accommodate the latch plate. Use a chisel for chiseling out the mortise for the latch making sure it's large enough to allow the faceplate of the new latch to be in a flush position with the doorjamb. Tape the strike plate in place to make sure it is positioned correctly.

If the strike is positioned too high, the door can be kicked in or pressure put on it using a crowbar, or tire iron. This could cause the doorjamb to crack. To fix this, the strike could be lowered by drilling another hole in the doorjamb and cutting out the core of the old hole.

The final step is to mount the new strike plate which is done by screwing it over the existing screw holes. Then apply wood putty to cover the holes from the previous screws and the bolt hole that is not used. After the putty has dried you can sand it down to give it a an elegant finish.

Strike

An electric strike is a metal part where the deadbolt and latch are engaged when the door is closed. It is an essential component of the lock's overall security because it prevents the door from opening, and also provides additional resistance to force or kick. If a door is equipped with an electric strike, it can only be opened with an entry key or the control unit which controls the electrical impulses.

Traditionally, installing an electric strike meant cutting out a portion of the doorjamb to remotely release a cylindrical lock's latchbolt from the pocket within the strike. This is a drawback when it comes to the appearance of openings as well as exposing the keeper mechanism and latchbolt to any unauthorised users.

Recently, a variety of electric strike manufacturers have created a "No Cut" type of strike that doesn't require a cutout in order to operate. These strikes have a unique design that allows the keeper and latchbolt to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp that raises the latchbolt and keeper when it receives the signal of an individual reader. The retracting of the keeper and latchbolt raises them on the ramp, which locks the door. When the door is closed the deadbolt remains in place and the latchbolt retracts into the keeper.

Installing an electric strike is a simple process, especially if you are replacing the strike on a previous door. However, if you're upgrading to an electric strike in an access control system, you will be required to ensure that the new system is compatible with the type of lock you've chosen to install. It is also necessary to ensure that the strike is properly connected to your access control system and set up to function in a fail-safe way.

Upgrade your strike plates to heavy duty strike plates to block unauthorised entry. These plates use up to six screws of three inches instead of two screws of three-fourths of an inch. These longer screws make it harder for anyone to break the frame and then reach inside to turn the piece that turns the thumb of a single deadbolt cylinder.